flue gas - an overview | sciencedirect topics

Flue Gas - an overview | ScienceDirect Topics

The flue gas exits the cyclones to a plenum chamber in the top of the regenerator. The hot flue gas holds an appreciable amount of energy. Various heat recovery schemes are used to recover this energy. In some units, the flue gas is sent to a CO boiler where both the sensible and combustible heat is used to generate high-pressure steam.

Get a Quote
flue temperature - an overview | sciencedirect topics

Flue Temperature - an overview | ScienceDirect Topics

A flue gas analysis of a gas-fired boiler indicates that the CO 2 content is 8% with a gas flue temperature of 204°C (400°F). Determine the overall thermal efficiency of the boiler. Solution. By reading the monograph of Fig. 8.12, the combustion occurs with an excess air of 48% and excess O 2 of 7%. The overall boiler thermal efficiency is

Get a Quote
high flue gas temperature - boiler and pressure …

HIGH FLUE GAS TEMPERATURE - Boiler and Pressure …

2004-11-15 · Can anybody help me on this. Our firetube boiler has a progressive increase in flue gas temperature due to the formation of unburned residue or soot inside the boiler. We have already check the flue gas analysis and its corresponds to the standard setting. CO2 = 12-15%, O2 = 3-5%. Any suggestions regarding this.

Get a Quote
what is the gas temperature coming out from the …

What is the gas temperature coming out from the …

The rated flue gas exit temperature at the air pre-heater outlet is around 135 deg Celsius in a typical sub-critical boiler. The flue gas temperature should always be maintained preferably within 120 to 150 deg Celsius. If it goes beyond 150 deg C

Get a Quote
flue gas temperatures and pvc venting - cause for …

Flue Gas Temperatures and PVC Venting - Cause for …

The high temperature of flue gases is a major concern to me due to the fact that Schedule 40 PVC pipe and fittings are only rated for 140 degrees Fahrenheit. I think we, in New England, are going to see PVC failures in the near future, directly related to the high flue gas temperatures of the new high-efficiency boilers. PVC Alternatives

Get a Quote
technical advice on boiler combustion control

Technical advice on boiler combustion control

: Noria Corporation

Combustion Efficiency and Excess Air - Engineering …

2020-3-20 · The relation between temperature difference in flue gas and supply air, the CO 2 concentration in the flue gas, and the efficiency loss in the flue gas oil combustion, is expressed below: Example - Oil Combustion and Heat Loss in the Flue Gas. If. the temperature difference between the flue gas leaving a boiler and the ambient supply

Get a Quote
flue gas temperature and heat in the flue gas flow …

Flue Gas Temperature and Heat in the Flue Gas Flow …

The flue gas temperature can be determine in this case by an iterative process of inputting the flue gas mass flows and an assumed flue gas temperature to see if the Total Flue Gas Btu/hr is equal to 21,194.31 Btu/hour, if not you try another assumed temperature.

Get a Quote
flue gas dew point temperatures - engineering toolbox

Flue Gas Dew Point Temperatures - Engineering ToolBox

2020-3-20 · Flue gas dew point temperatures and the condensation of water vapor . Flue gas dew point temperature is the temperature where condensation of water vapor in the flue gas starts. Dew Point Temperature of Flue Gases (pdf) Sponsored Links . Related Topics . Combustion - Boiler house topics - fuels like oil, gas, coal, wood - chimneys, safety

Get a Quote
5 factors killing your industrial boiler efficiency & …

5 Factors Killing Your Industrial Boiler Efficiency & …

Net stack temperature is the difference between the flue gas temp and the ambient temperature. Although it's tempting to minimize ambient temperature with hopes of lowering flue gas temp, a 40 degree alteration in ambient temperature can affect industrial boiler efficiency by one percent or more.

Get a Quote